Wayne 350705-001 Manuale Utente Scaricare il pdf

Please read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain the product described.

Protect yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury and/or

property damage! Retain instructions for future reference.

Description

The submersible pump is designed for home

sump applications. The unit is equipped with

an 8-ft long, 3-prong grounding type power

cord. Motor is oil filled and sealed for cooler

running and designed to operate under

water. A float switch is provided for

automatic pump operation. This pump is not

suitable for aquatic life.

Unpacking

Inspect this unit before it is used.

Occasionally, products are damaged during

shipment. If the pump or components are

damaged, return the unit to the place of

purchase for replacement. Failure to do so

could result in serious injury or death.

General Safety Information

Do not use to pump

flammable or explosive

fluids such as gasoline,

fuel oil, kerosene, etc. Do

not use in a flammable and/or explosive

atmosphere. Pump should only be used

to pump clear water. Personal injury

and/or property damage could result.

This pump is not

designed to handle

salt water, brine, laundry discharge or

any other application which may

contain caustic chemicals and/or

foreign materials. Pump damage could

occur if used in these applications and

will void warranty.

All wiring must be

performed by a

qualified electrician. Failure to follow

this warning could result in fatal

electrical shock.

If the basement has water

or moisture on the floor,

do not walk on wet area

until all power is turned

off. If the shutoff box is

in the basement, call an electrician.

Remove pump and either repair or

replace. Failure to follow this warning

could result in fatal electrical shock.

Operating Instructions and Parts Manual Submersible Series

350705-001 7/05

A backup system

should be used.

Wayne offers Model ESP15.

Assembly

VERTICAL FLOAT SWITCH (FLOAT ONLY)

Place the float bracket onto the handle of

the motor housing and slide the switch

assembly securely into place.

Installation

1. Install pump in a sump pit with minimum

size as shown in Figure 2. Construct

sump pit of tile, concrete, steel or plastic.

2. The unit should be located and rest on a

solid, level foundation. Do not place

pump directly on clay, earth, gravel or

sandy surface. These surfaces contain

small stones, gravel, sand, etc. that may

clog or damage the pump and cause

pump failure.

Flood risk. If

flexible discharge

hose is used, make sure pump is

secured in sump pit to prevent

movement. Failure to secure pump

could allow pump movement and

switch interference and prevent pump

from starting or stopping.

3. Thread check valve (Wayne offers Model

66005-WYN) into pump body carefully

to avoid stripping or cross threading. Do

not use pipe joint sealant.

4. Connect 1-1/2” rigid pipe to rubber boot

on check valve. Reverse boot for 1-1/4”

diameter pipe. Tighten hose clamps.

Support pump and

piping when

assembling and after installation.

Failure to do so could cause piping to

break, pump to fail, etc. which could

result in property damage and/or

personal injury.

5. Protect electrical cord from sharp object,

hot surfaces, oil and chemicals. Avoid

kinking the cord and replace damaged

cords immediately.

IMPORTANT: Make sure there is adequate

room for the switch to operate.

6. A sump pit cover must be installed to

prevent debris from clogging or

damaging the pump.

Operation

Always disconnect the

power source before

attempting to install,

service, relocate or maintain the pump.

Never touch sump pump, pump motor,

water or discharge piping when pump is

connected to electrical power. Never

handle a pump or pump motor with wet

hands or when standing on wet or damp

surface or in water. Fatal electrical

shock could occur.

1. A ground fault circuit interrupter (GFCI)

is required.

Figure 2

Float 11”

Tether 14”

Min. Diameter

Switch Housing

Float

Bracket

Figure 1

Submersible

Sump Pump

For parts, product & service information

visit www.waynepumps.com

REMINDER: Keep your dated proof of purchase for warranty purposes! Attach it to this manual or file it for safekeeping.

1 2 3 4 5 6 7 8

Sommario

Pagina 1 - Sump Pump

Please read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain the product described.Protect your

Pagina 2 - Construction

4. Fill sump with water. The pump will startautomatically when the water has filledthe sump to the cut-in level. The pumpwill stop when the water re

Pagina 3 - Limited Warranty

3Operating Instructions and Parts Manual1 Tether Float Switch Kit (WST) 60022-001 60022-001 60022-001 60022-001 60022-001 —2 Motor Assy Kit 60046-001

Pagina 4 - Pompe de

MÉMENTO: Gardez votre preuve datée d'achat à fin de la garantie! Joignez-la à ce manuel ou classez-la dans un dossier pour plus de sécurité. répa

Pagina 5 - Fabrication

démarrage/coupage. La pompefonctionnera automatiquement si exigée.5. Ne pas faire fonctionner la pompe si ellen’est pas submergée dans l’eau. Lefoncti

Pagina 6 - Sumergible

RECORDATORIO: ¡Guarde su prueba de compra con fecha para fines de la garantía! Adjúntela a este manual o archívela en lugar seguro.Sírvase leer y guar

Pagina 7 - Materiales de Fabricación

4. Llene el sumidero de agua. La bomba seencenderá automáticamente tan prontocomo el nivel de agua haya alcanzado elnivel mínimo fijado de fábrica.

Pagina 8 - Garantie Limitée

Manual de Instrucciones y Lista de RepuestosGarantía LimitadaDurante el 90 dias a partir de la fecha de compra, Wayne Water Systems Division ("Wa